Ancient Clarinet Mouthpiece Thread

Started by Windsong, October 10, 2026, 10:37:40 AM

Previous topic - Next topic

Windsong

For perusal and comparison, in respective order, are three mouthpieces:

1) An Austro-Hungarian Key of D mouthpiece (1870s-1880s)

2) An 1860s-1880s Austro-Hungarian Key of Eb mouthpiece (the Austro-Hungarians also used this size for Key of C horns)

3) A modern Woodwind Co. "Imperial" Eb mouthpiece, with shaved tenon for fitment in small bore Ebs.
Expert bubblegum welder, and Pedler Pedler.

Windsong

Here are dimensions of the D mouthpiece, to show how diminutive it is.

Expert bubblegum welder, and Pedler Pedler.

Windsong

Bore = .483"
Table length 2.25"
Tenon length = .500"
Outer Tenon cork lip = .710"
Window length = .985"
Window width, base = .280"
Window width, tip = .395"
Expert bubblegum welder, and Pedler Pedler.

Jeabrams

#3
Ok then I have a bit of work to do!
These are the original wooden mouthpiece and the printed reproduction for my Ab Buffet c18xx?
Inside dia. 0.19-0.20
Length.     2.25"
Table.      .765"
Window length.7625
Window base width 0.20
Window top width 0.3285"
Tenon
 height 0.475"
Tenon lip outer 0.602
Tenon lip inner cork dia 0.585"
Reed height 0.0440"
Information technology Retiree - professional band instrument tech, artist, musician, and generally busy with stuff!

Jeabrams

Here are three printed examples-
Bb, Eb, Ab.... I also have printed EbAlto and Bass mouthpieces.

And a photo of measuring the reed height.
Information technology Retiree - professional band instrument tech, artist, musician, and generally busy with stuff!

Windsong

Impressive stuff!

I don't have the ability to take reed height in that fashon.  I had a really nice dial gage,  but the tension spring broke, and it was not cheap(!), so I have been lax about replacing it.
Expert bubblegum welder, and Pedler Pedler.

Jeabrams

#6
Not an issue really. Nice thing to know but not a problem. Most facings are in a narrow window and depending on reed strength (most of us seem to like the 2.5 or 3's) so I can make a guess at about .043'ish. If you have a way to find the pitch of the Mouthpiece by itself that can help. Voicing is very dependent on the mouthpiece/reed pitch being "right" so everything else falls into place.
My Eb Yamaha mp by itself has a nice 740hz f#5
The Ab mp is 936hz Bb5
Most of the Bb mp's seem to hover around Bb5 as well. Just don't want to make something that looks good but won't work 😉😁
Information technology Retiree - professional band instrument tech, artist, musician, and generally busy with stuff!

Windsong

#7

I typically use 3.5 strength reeds.  The exception is with these C, D and Eb clarinets, where, due to the reduced dimensions, a 3.5 feels way too stiff, so I drop back to 2.5s.

Here are additional measurements:

MP diameter (At base, just above tenon) = .946" (24.03mm)

MP diameter @ table (At base, just above tenon) = .892" (22.65mm)
Expert bubblegum welder, and Pedler Pedler.

Jeabrams

so after some fumbling with new materials and having fun with shrinkage and other delemmas.  And even a swing and a miss.....  here is a likely replacement for the D mouthpiece. If one of my attempts works then ill print a few more and save the files for the future.
Information technology Retiree - professional band instrument tech, artist, musician, and generally busy with stuff!

Jeabrams

Information technology Retiree - professional band instrument tech, artist, musician, and generally busy with stuff!

Windsong

That is VERY nice looking.  I am really impressed with the finish; not at all the 3D printing of 10 years ago!
Expert bubblegum welder, and Pedler Pedler.

Jeabrams

So after reviewing your measurements and checking the latest attempt I decided to print a couple more. These three are tests for you to try. You will find one is light the other two heavier. The heavy ones are more dense and should sound different. All are set at .040-.042 so should use the same reed. 
Information technology Retiree - professional band instrument tech, artist, musician, and generally busy with stuff!

Windsong

#12
I await those with 'bated breath.  They sure look good.  You're a gentleman and a scholar.
Expert bubblegum welder, and Pedler Pedler.

Jeabrams

More like a gelatin in a schoolyard - but thanks
Information technology Retiree - professional band instrument tech, artist, musician, and generally busy with stuff!

Windsong

Expert bubblegum welder, and Pedler Pedler.